Yunfei brand solar insect situation report installation and use method

1) the tank to the flat, but where the distance near the target pest activity.

2) Check if the battery, controller and solar panel are secure.

3) from the lamp varies mountain, level terrain, the distance should be 50 m -80 m (i.e., covers over an area of 50 acres between -100 mu).

4) The pest test light should be installed in a higher position to avoid flooding.

5) Working status indication

a). Battery board indication: When the output voltage of the solar panel reaches a certain value, the solar battery indicator light is on; when the battery is started to be charged, the solar panel indicator light flashes slowly; when the system is over pressure, the indicator light flashes rapidly.

b). Battery indication: When the battery is under voltage, the battery indicator light flashes slowly; when the battery status is over-discharged, the battery indicator light flashes quickly and the load is turned off; when the battery status is normal, the battery indicator light is on.

c). Load indication: When the load is working normally, the load indicator light is always on; when the load is over applied, the load indicator light flashes slowly. When the power supply exceeds the rated current by 1.25 times for 30s , or the current exceeds the rated current by 1.5 times for 5s , the controller The load will be turned off; when the load is short-circuited, the controller immediately turns off the load-free and the load indicator flashes quickly.

6) Setting method

Press the SET button for more than 3s and the digital tube starts to flash. The system enters the adjustment mode and releases the button. Each time the button is pressed, the digital tube number will be changed to a number until the number displayed by the digital tube corresponds to the mode selected by the user from the table. The number is up, and the digital tube stops flashing or the button is pressed for more than 3 seconds to complete the setting.

7) Introduction to the mode

Pure light control : When there is no sunlight, the light intensity drops to the starting point. After the controller delays for 10 minutes to confirm the start signal, the load is turned on according to the setting parameters, and the load starts to work; when there is sunlight, the light intensity rises to the starting point, and the control Delay 10 minutes after confirming the shutdown signal   The load stops working.

Light control + time control: The starting process is the same as pure light control. When the load reaches the set time, the load will be turned off. The setting time is shown in the table below.

Manual mode: In this mode, the user can control the opening and closing of the load by pressing the button, regardless of whether it is during the day or night. This mode is used for some special load situations or for debugging purposes.

Debug mode: It is used for system debugging. When there is an optical signal, the load is not turned off and the load is turned on, which is convenient for checking the installation of the system during installation and debugging.

Normally open mode: The power supply load is always in the output state. This mode is suitable for loads that require 24 hours of power supply.

8) Working mode setting table

Common faults and troubleshooting methods

1) The lamp is not bright

a). Check if the lamp is damaged.

b). Is the battery powered?

c). Is the solar panel charging normal?

2) Insufficient battery battery

a). Is charging normal?

b). Is the battery board damaged?

Monobenzone

Monobenzone can decompose melanin in the skin, and prevent the formation of melanin in the skin, used for the treatment of hyperpigmentation, such as various spots, age spots, melanoma. In addition as intermediates in organic synthesis.

Our company offers variety of products which can meet your multifarious demands.including API Powder.Pharmaceutical Intermediates.Vitamins Powder.Plant Extracts.Food Additive.Peptide Powder and so on We adhere to the management principles of "quality first, customer first and credit-based" since the establishment of the company and always do our best to satisfy potential needs of our customers. Our company is sincerely willing to cooperate with enterprises from all over the world in order to realize a win-win situation since the trend of economic globalization has developed with anirresistible force.

Function:

1.Monobenzone is a compound used as a topical drug for medical depigmentation.

2.The topical application of monobenzone powder in animals decreases the excretion of melanin from melanocytes. The same action is thought to be responsible for the depigmenting effect of the drug in humans.

3.Monobenzone may cause destruction of melanocytes and permanent depigmentation.

4.The histology of the skin after depigmentation with topical monobenzone powder is the same as that seen in vitiligo.

5.The epidermis is normal except for the absence of identifiable melanocytes.

product Photo:

Best Monobenzone,Type 1 3 Collagen,99% Rapamycine Sirolimusa Powder,Hyaluronic Acid Dical

Shaanxi YXchuang Biotechnology Co., Ltd , https://www.peptide-nootropic.com